Supermarine Urethane
(SM-2000)
is versatile, good looking and as durable as it gets!
This two-part urethane has been specifically formulated to
provide superior adhesion, hardness, chemical, heat resistance
and durability than any consumer brand epoxy, alkyd, urethane or
resin blend. It’s a fully submersible self leveling formula
producing superior color and gloss retention so it is acceptable
for use in the engine room or bilge area. A military formula
that conforms to specification number MIL-P-85285 so you know
you are getting the best!
Supermarine
Urethane is a two-component aliphatic urethane designed for
extra durability and resistance to strong chemicals, heat,
spilled fuel, acids, alkalis, solvents, salt spray and corrosion
over a variety of substrates. Use it on any interior surface
including in the engine room, on engine components, exhaust
manifolds and pump housings. A fully submersible coating
acceptable for use on virtually all interior/exterior marine
surfaces without yellowing or chalking. Acceptable for use on
prepared iron, steel, aluminum, fiberglass and wood. Resists
heat (500F), chemicals, fuels and staining agents.
-
10 Year Guaranty.
-
Guaranteed to withstand a
sulfuric acid spill for 7 days!
-
Produces an exceptionally
hard scuff resistant finish.
-
Withstands heat to 500F.
-
Maintains its color and
gloss without chalking yellowing or fading.
-
Resists cracking, peeling
and chalking.
-
Provides superior adhesion,
hardness, flexibility and durability.
-
Buffing easily removes mars
and abrasions.
-
Spray: up to 600 sq ft per
gallon! Brush & Roll up to 400 sq ft per gallon.
-
Self leveling formula
reduces brush and roller marks.
-
Resists heat from 60 degrees
below zero to over 500F, impacts to 500 PSI.
-
Acceptable for low
temperature applications to 20F.
-
Produces beautiful finish
available in 100 colors plus clear.
Stats:
Covers 400-600 square feet per gallon depending on surface and
specific application requirements. Dry to the touch in 30
minutes-1 hour. Mixing Ratio: 7:1 (by volume) with Part B
(Induction Time: 15 minutes) Pot life: 4 hours * It is supplied
at spray viscosity suitable for most conventional systems.
Compatible for electrostatic spray. Low temperature curing (as
low as 20 F.) Available in 100 marine paint colors. Custom
colors available on request for an additional $10 per gallon.
Recommended preparation:
Refer to Application Instructions Sheet included with order,
label directions and standard industry application practices.
For best results remove old paint, loose scale, wax, oil and
contaminates. Sand or scuff all surfaces prior to the
application of any primer or coating.
Fiberglass, aluminum,
concrete, masonry and stainless steel, galvanized steel-
strongly recommend the use of
SM-695
Etching Cleaner.
All wood surfaces must be thoroughly
cleaned and dry before the application of primer or coatings.
Steel: Where rust is evident
recommend
SM-5679 Phos-Pro Rust
Converting Cleaner. All surfaces must be thoroughly dry
and free of contaminates before the application of any primer or
marine paint.
Recommended primers:
Aluminum, galvanized and stainless steel-
SM-117 Pre-Wash Primer
in combination with SM-787 Mono-Coat Epoxy Primer,
SM-664D
Etching Primer.
Steel & iron:
SM-7390 Formula 150 Epoxy Primer
or
SM-664D Etching Primer.
.
Concrete &
masonry-
SM-7390 Formula 150 Epoxy Primer
Wood-
SM-664D Etching Primer.
Thin & clean up:
Use only with factory recommended thinner,
SM-605 Thinne. Clean all
equipment thoroughly with
SM-605 Thinner.
